{
  "design": "Slow Bloom",
  "issue": "NDY-3",
  "effective": "2026-11-01",
  "purpose": "Geometry, mass and wind-catch data for the concept 'Slow Bloom' as drawn, prepared as INPUT to a structural check. This is not a structural analysis and contains no design values.",
  "datum": {
    "x_ft": "distance along the boom from the yaw (main ring) axis; +x is outboard, -x is the counterweight end",
    "z_ft": "height above finished grade",
    "note": "Boom pivot is 4 ft from the butt, so the boom spans x = -4.0 ft to +8.0 ft. Mast top / ring / boom centreline are all at z = 7.5 ft."
  },
  "geometry_as_built": {
    "grade_to_mast_top_ft": 7.5,
    "pier": {
      "diameter_in": 12,
      "depth_below_grade_in": 36,
      "above_grade_in": 2,
      "total_length_in": 38,
      "reinforcement": "4 x #4 (1/2 in) A615 Gr 40 vertical bars, wired cage",
      "concrete": "Quikrete 1101 bagged concrete mix (BOM A1), 5 x 80 lb bags for a 38 in x 12 in pier (2.49 cu ft at 0.6 cu ft/bag)",
      "soil": "unknown - no geotechnical information exists for this site"
    },
    "mast": {
      "section": "4 in nominal Schedule 40 pipe, 4.50 in OD x 0.237 in wall, A500 ERW",
      "length_in": 90,
      "length_ft": 7.5,
      "mass_lb_per_ft": 10.79,
      "section_area_in2": 3.17,
      "section_I_in4": 7.24,
      "section_S_in3": 3.22,
      "base_fixity": "12 x 12 x 3/4 in A36 base plate welded to the foot, four 2 x 2 x 1/4 in angle gussets, four 3/4 in x 8-1/2 in Titen HD screw anchors into the cured pier"
    },
    "boom": {
      "section": "2-1/2 in OD x 0.120 in wall, A513 welded HREW",
      "length_ft": 12,
      "pivot_offset_from_butt_ft": 4,
      "mass_lb_per_ft": 3.05,
      "note": "Straight tube; the taper in the silhouette comes from the stalks and the counterweight, not the tube."
    },
    "bloom_rotor": {
      "count": 5,
      "bowl": "8 qt stainless mixing bowl, 13-1/4 in dia x 4 in deep, 0.4 mm stainless, cut in half on its diameter",
      "lobe_offset_from_axis_in": 1.5,
      "clear_space_between_lobes_in": 1.25,
      "rotor_width_over_lobes_in": 14.5,
      "rotor_height_in": 4,
      "frontal_silhouette_each_sqft": 0.263,
      "swept_area_each_sqft": 0.403,
      "area_note": "Frontal silhouette per bloom is the circular segment of a 13.25 in chord / 4 in deep spherical cap: R = (r^2 + h^2)/(2h) = 7.49 in, segment area = R^2 (theta - sin theta)/2 with theta = 2 asin(r/R) = 2.1726 rad -> 37.9 sq in = 0.263 sq ft. Two offset lobes at +/-1.5 in do not overlap in projection, so the rotor silhouette is about the same as the whole bowl. The 0.403 sq ft figure is the Savonius convention (rotor width x height = 14.5 in x 4 in) used for the rotor's efficiency, not for load.",
      "bloom_centres_from_butt_ft": [6.0, 7.417, 8.833, 10.167, 11.583],
      "bloom_centres_above_boom_in": [42, 36, 30, 24, 18],
      "stalk_lengths_in": [40, 34, 28, 22, 16],
      "stalk_section": "1-1/2 in OD x 0.120 in wall A513"
    },
    "wind_areas_carried_by_the_mast_itself": "the mast (4.50 in OD x 7.5 ft) presents 2.81 sq ft below the ring and is carried directly to the base plate and anchors - listed as a wind area, fixed, not rotating"
  },
  "components": [
    { "id": "mast-pipe", "group": "fixed", "item": "Mast pipe, 4 in Sch 40, 7.5 ft", "tube": { "od_in": 4.5, "wall_in": 0.237, "length_ft": 7.5, "material": "steel" }, "x_ft": 0.0, "z_ft": 3.75, "source": "BOM A4" },
    { "id": "base-plate", "group": "fixed", "item": "Base plate, A36, 12 x 12 x 3/4 in", "plate": { "area_sqin": 144.0, "thickness_in": 0.75, "material": "steel" }, "x_ft": 0.0, "z_ft": -0.08, "source": "BOM A5" },
    { "id": "base-gussets", "group": "fixed", "item": "Four base gussets, 2 x 2 x 1/4 angle x 8 in", "mass_lb": 8.5, "x_ft": 0.0, "z_ft": 0.67, "source": "BOM A6 note, 3.19 lb/ft" },
    { "id": "head-fixed-plate", "group": "fixed", "item": "Fixed head adapter plate, A36, 7 x 7 x 1/2 in", "plate": { "area_sqin": 49.0, "thickness_in": 0.5, "material": "steel" }, "x_ft": 0.0, "z_ft": 7.5, "source": "BOM B2, one 12 x 12 blank yields both plates" },
    { "id": "drip-hat", "group": "fixed", "item": "Inverted 1 qt stainless bowl (drip hat)", "mass_lb": 0.5, "x_ft": 0.0, "z_ft": 7.5, "source": "BOM B3, estimated" },

    { "id": "head-rotating-plate", "group": "rotating", "item": "Rotating head plate, A36, 7 x 7 x 1/2 in", "plate": { "area_sqin": 49.0, "thickness_in": 0.5, "material": "steel" }, "x_ft": 0.0, "z_ft": 7.5, "source": "BOM B2" },
    { "id": "yoke-cheeks", "group": "rotating", "item": "Two nod yoke cheeks, A36, 8 x 6 x 1/4 in", "plate": { "area_sqin": 96.0, "thickness_in": 0.25, "material": "steel" }, "x_ft": 0.0, "z_ft": 7.2, "source": "BOM E5 cut list" },
    { "id": "yoke-brackets", "group": "rotating", "item": "Four small brackets / gussets from the E5 plate", "mass_lb": 1.6, "x_ft": 0.0, "z_ft": 7.2, "source": "BOM E5 cut list, estimated" },
    { "id": "boom-tube", "group": "rotating", "item": "Boom tube, 2-1/2 in OD x 0.120 x 12 ft", "tube": { "od_in": 2.5, "wall_in": 0.12, "length_ft": 12.0, "material": "steel" }, "x_ft": 2.0, "z_ft": 7.5, "source": "BOM D1 note, 3.05 lb/ft, 3.05 x 12 = 36.6 lb" },
    { "id": "fulcrum-cross-tubes", "group": "rotating", "item": "Four fulcrum cross-tubes, 6 in each, same tube as the boom", "tube": { "od_in": 2.5, "wall_in": 0.12, "length_ft": 2.0, "material": "steel" }, "x_ft": 0.0, "z_ft": 7.5, "source": "BOM D1 cut list" },
    { "id": "nod-pivot-pin", "group": "rotating", "item": "Nod pivot pin, 1 in 1018 bar x 7 in", "solid_bar": { "diameter_in": 1.0, "length_ft": 0.583, "material": "steel" }, "x_ft": 0.0, "z_ft": 7.5, "source": "BOM C2" },
    { "id": "counterweight-stub", "group": "rotating", "item": "Counterweight stub, 1 in 1018 bar x 5 in, coaxial in the butt", "solid_bar": { "diameter_in": 1.0, "length_ft": 0.417, "material": "steel" }, "x_ft": -4.2, "z_ft": 7.5, "source": "BOM C2" },
    { "id": "counterweight", "group": "rotating", "item": "Counterweight, 2 x 25 lb CAP cast iron plates, slid onto the stub", "mass_lb": 50.0, "x_ft": -4.25, "z_ft": 7.5, "source": "BOM D4, nominal plate mass; slides over the 5 in stub so x is -4.0 to -4.4 ft" },
    { "id": "boom-end-caps", "group": "rotating", "item": "Boom end caps and weep fittings", "mass_lb": 0.5, "x_ft": 4.0, "z_ft": 7.5, "source": "BOM D5, estimated" },

    { "id": "stalk-1", "group": "rotating", "item": "Bloom stalk 1, 1-1/2 in OD x 0.120 x 40 in", "tube": { "od_in": 1.5, "wall_in": 0.12, "length_ft": 3.333, "material": "steel" }, "x_ft": 2.0, "z_ft": 9.17, "source": "BOM D2, 1.77 lb/ft" },
    { "id": "stalk-2", "group": "rotating", "item": "Bloom stalk 2, 34 in", "tube": { "od_in": 1.5, "wall_in": 0.12, "length_ft": 2.833, "material": "steel" }, "x_ft": 3.417, "z_ft": 8.92, "source": "BOM D2" },
    { "id": "stalk-3", "group": "rotating", "item": "Bloom stalk 3, 28 in", "tube": { "od_in": 1.5, "wall_in": 0.12, "length_ft": 2.333, "material": "steel" }, "x_ft": 4.833, "z_ft": 8.67, "source": "BOM D2" },
    { "id": "stalk-4", "group": "rotating", "item": "Bloom stalk 4, 22 in", "tube": { "od_in": 1.5, "wall_in": 0.12, "length_ft": 1.833, "material": "steel" }, "x_ft": 6.167, "z_ft": 8.42, "source": "BOM D2" },
    { "id": "stalk-5", "group": "rotating", "item": "Bloom stalk 5, 16 in", "tube": { "od_in": 1.5, "wall_in": 0.12, "length_ft": 1.333, "material": "steel" }, "x_ft": 7.583, "z_ft": 8.17, "source": "BOM D2" },
    { "id": "stalk-collars", "group": "rotating", "item": "Five stalk collars, 1-1/4 in OD x 3/16 in DOM x 3 in", "tube": { "od_in": 1.25, "wall_in": 0.1875, "length_ft": 1.25, "material": "steel" }, "x_ft": 4.6, "z_ft": 7.65, "source": "BOM D3 note, 2.14 lb/ft" },
    { "id": "bloom-rotors", "group": "rotating", "item": "Five bloom rotors complete (bowl 0.95 lb, hub 0.33 lb, two hub caps 1.18 lb, axle 0.09 lb, two bearings 0.05 lb each)", "mass_lb": 13.0, "x_ft": 4.8, "z_ft": 10.0, "source": "bowl from cap area 188 sq in x 0.01575 in x 0.29 lb/in3 = 0.86 lb, rounded to 0.95; hub from BOM E2 note 0.66 lb/12 in; hub caps from E5 discs; x is the mass-weighted mean of the five bloom positions" },
    { "id": "axle-sleeves", "group": "rotating", "item": "3/4 in stainless sleeve / spacer stock as used (about 1.5 ft)", "tube": { "od_in": 0.75, "wall_in": 0.049, "length_ft": 1.5, "material": "stainless316" }, "x_ft": 4.8, "z_ft": 9.5, "source": "BOM E6" },
    { "id": "bowl-clamps", "group": "rotating", "item": "Five bowl-to-hub clamps, 1/4 x 2 in flat bar x 6 in", "mass_lb": 4.25, "x_ft": 4.8, "z_ft": 9.5, "source": "BOM E7 note, 1.70 lb/ft x 2.5 ft" },
    { "id": "fasteners-rotating", "group": "rotating", "item": "Stainless fasteners in the rotating group (bolts, nuts, washers)", "mass_lb": 4.0, "x_ft": 4.0, "z_ft": 8.5, "source": "BOM F2-F8, estimated from unit masses of the listed quantities" }
  ],
  "wind_areas": [
    { "id": "bloom-1", "item": "Bloom 1 rotor, frontal silhouette", "area_sqft": 0.263, "x_ft": 2.0, "z_ft": 11.0, "note": "highest and innermost bloom" },
    { "id": "bloom-2", "item": "Bloom 2 rotor", "area_sqft": 0.263, "x_ft": 3.417, "z_ft": 10.5 },
    { "id": "bloom-3", "item": "Bloom 3 rotor", "area_sqft": 0.263, "x_ft": 4.833, "z_ft": 10.0 },
    { "id": "bloom-4", "item": "Bloom 4 rotor", "area_sqft": 0.263, "x_ft": 6.167, "z_ft": 9.5 },
    { "id": "bloom-5", "item": "Bloom 5 rotor", "area_sqft": 0.263, "x_ft": 7.583, "z_ft": 9.0, "note": "outermost bloom, longest lever arm" },
    { "id": "blooms-all", "item": "All five bloom rotors (summary line, not added again)", "area_sqft": 1.315, "x_ft": 4.8, "z_ft": 10.0, "role": "summary" },
    { "id": "stalks", "item": "Five bloom stalks, 1-1/2 in OD, 140 in total", "area_sqft": 1.458, "x_ft": 4.65, "z_ft": 8.6, "note": "cylinder, 1.5 in dia x 11.67 ft total; centroid x is the length-weighted mean of the five stalk positions" },
    { "id": "boom", "item": "Boom tube, 2-1/2 in OD x 12 ft", "area_sqft": 2.5, "x_ft": 2.0, "z_ft": 7.5 },
    { "id": "boom-end-caps-and-collars", "item": "End caps, collars and the counterweight", "area_sqft": 1.0, "x_ft": -2.0, "z_ft": 7.5, "note": "counterweight discs 25 lb at 1 in bore, roughly 9 in dia, plus collars; estimated" },
    { "id": "head-and-yoke", "item": "Head plates and nod yoke", "area_sqft": 1.0, "x_ft": 0.0, "z_ft": 7.4, "note": "a 12 in square plate stack read as 1 sq ft of projected area; estimated" },
    { "id": "mast", "item": "Mast, 4.50 in OD x 7.5 ft (below the ring, carried straight to the base)", "area_sqft": 2.81, "x_ft": 0.0, "z_ft": 3.75, "role": "fixed" }
  ],
  "wind": {
    "speed_mph": 115,
    "basis": "3-second gust, Exposure Category C, Grand County Design Criteria and adopted code (county also states that special wind regions exist in Grand County)",
    "source": "docs/references.md, section 2",
    "kz": 0.85,
    "kz_basis": "ASCE 7 velocity pressure exposure coefficient for Exposure C at 0-15 ft; the top of the piece is 11.5 ft up, so the whole piece sits inside that band",
    "velocity_pressure_formula": "qz = 0.00256 * V^2 * Kz",
    "factors_left_to_the_engineer": ["Kd (wind directionality)", "G (gust effect factor)", "Cf / GCp shape factors for a 12 ft cantilever tube carrying five drag rotors", "altitude and air density (site is at about 7,300 ft)", "the possibility that the county will require a higher speed in a special wind region"]
  },
  "known_unknowns_left_to_the_engineer": [
    "soil bearing, lateral capacity and stiffness at the pier (no geotechnical data exists)",
    "the compressive strength actually achieved by the bagged concrete mix in a 12 in sonotube",
    "code basis and load combinations the county will accept (IBC/ASCE 7 edition, and any local amendment for this county's special wind region)",
    "the fatigue and dynamic-amplification question: a 12 ft cantilever with five rotating drag devices is not a static structure",
    "the anchor design: four 3/4 in Titen HD screw anchors in a 12 in pier, combined tension and shear, edge distance and spacing in a 12 in diameter concrete cylinder"
  ]
}
