{
  "design": "Slow Bloom",
  "issue": "NDY-3",
  "effective": "2026-11-01",
  "currency": "USD",
  "status": "APPROVED 2026-11-01 - UPDATED TO MIKE'S CHOSEN PARTS. NOTHING ORDERED, NOTHING CUT.",
  "decisions_applied": {
    "date": "2026-11-01",
    "source": "Mike's five decisions - recorded at the top of this project's .hermes.md and delivered under Paperclip issue NDY-3",
    "1_colours": "charcoal-green stem, marigold blooms, clay-red interiors (pairing 1, the warm one). No BOM line changes. It does create one open item: the chosen finish product is a fixed-palette enamel that cannot be tinted - see the notes on line F3 and the 'Coating colour' item in the concept sheet.",
    "2_main_ring": "the FULLY SEALED ring PRT-01-100-DD (B1), not the standard ring. The 25-30 working day lead time is accepted and is now a hard constraint on the build schedule. igus publishes no price for the -DD variant, so B1 is the one line in this bill carried as an allowance rather than a quoted price - it is still the only unpriced line, and it says so.",
    "3_finish": "single-can direct-to-metal enamel (F3) instead of the marine two-part LPU. F1 (epoxy barrier-coat primer) and F2 (two-part LPU topcoat) were deleted on 2026-11-01 and F3 was promoted from alternate to primary. Line ids were deliberately NOT renumbered, so F1 and F2 are absent from this file - they were removed, not lost.",
    "4_blooms": "the thin 0.4 mm bowl at $17.29 each (E1), confirmed as the chosen bowl. It will dent; cheap to replace is the trade accepted, and the notes on E1 say so rather than pretending it is a tough part.",
    "5_structural": "the structural check is to be done by a licensed structural engineer before any metal is cut. It has NOT been done here and must not be. What was produced instead is the input package that check needs: docs/slow-bloom-structural-brief.md, whose numbers come from output/slow-bloom-load-inputs.json run through scripts/slow_bloom_loads.py."
  },
  "verification_legend": {
    "page": "price read directly off the vendor's own product page on 2026-11-01",
    "listing": "price taken from the vendor's own listing/summary (search snippet or category page), product page not fully readable",
    "store": "product is real but the vendor publishes no online price (store-only item)",
    "quote": "the vendor does not publish a price and quotes on request; the figure carried is an allowance, not a quotation - the line's notes state exactly what the allowance is and what it is based on"
  },
  "items": [
    {
      "id": "A1",
      "category": "A. Foundation and mast",
      "item": "Concrete mix, 80 lb bag (Quikrete 1101 Concrete Mix)",
      "used_for": "Cast-in pier, 12 in dia x 36 in deep",
      "part_number": "110180 (Quikrete 1101 line)",
      "price_usd": 6.47,
      "unit": "per 80 lb bag",
      "qty": 5,
      "vendor": "The Home Depot",
      "url": "https://www.homedepot.com/p/Quikrete-80-lb-Concrete-Mix-110180/100318511",
      "verified": "listing",
      "role": "primary",
      "notes": "A 12 in dia x 36 in pier is 2.36 cu ft; one 80 lb bag yields about 0.6 cu ft, so 4 bags fill it. Buy 5. Home Depot bot-walls the browser; price from the HD listing. Page-verified alternate: McCoys Quikrete 1101-80 at $5.99 (https://www.mccoys.com/shop/p/04020002)."
    },
    {
      "id": "A2",
      "category": "A. Foundation and mast",
      "item": "Sonotube 12 in x 4 ft removable concrete forming tube",
      "used_for": "Pier form, 12 in dia x 36 in (cut 4 ft tube down to 3 ft)",
      "part_number": "Menards Sku # 1895159",
      "price_usd": 17.38,
      "unit": "each",
      "qty": 1,
      "vendor": "Menards",
      "url": "https://www.menards.com/main/building-materials/concrete-cement-masonry/concrete-forms/c-5653.htm",
      "verified": "listing",
      "role": "primary",
      "notes": "Menards lists this at $17.38 each. Home Depot's SAKRETE 12 in x 48 in tube is the same product but HD publishes no online price for it (store-only). NOTE: a 14 in tube, used in the earlier draft, has no online price anywhere - the 12 in size is the one that can actually be priced and bought online."
    },
    {
      "id": "A3",
      "category": "A. Foundation and mast",
      "item": "Rebar #4 (1/2 in) x 4 ft, A615 Grade 40",
      "used_for": "Pier reinforcement - 4 vertical bars",
      "part_number": "RB12",
      "price_usd": 7.80,
      "unit": "each",
      "qty": 4,
      "vendor": "Metals Depot",
      "url": "https://www.metalsdepot.com/steel-products/steel-rebar",
      "verified": "page",
      "role": "primary",
      "notes": "Stocked 2/4/6/8/10/20 ft; 4 ft = $7.80, 10 ft = $14.20."
    },
    {
      "id": "A4",
      "category": "A. Foundation and mast",
      "item": "Steel pipe, 4 in nominal Schedule 40 (4.50 in OD x 0.237 wall), A500 ERW, 8 ft",
      "used_for": "Mast - welded to the base plate, set 7 ft 6 in above grade",
      "part_number": "T54",
      "price_usd": 361.00,
      "unit": "each",
      "qty": 1,
      "vendor": "Metals Depot",
      "url": "https://www.metalsdepot.com/steel-products/steel-pipe",
      "verified": "page",
      "role": "primary",
      "notes": "10.79 lb/ft, so the 8 ft mast is 86 lb. Stocked 1/2/4/6/8/10/21 ft; 8 ft = $361.00. Heavy - ships freight."
    },
    {
      "id": "A5",
      "category": "A. Foundation and mast",
      "item": "Steel plate, A36, 12 x 12 x 3/4 in, cut to size",
      "used_for": "Base plate welded to the foot of the mast",
      "part_number": "9614",
      "price_usd": 232.21,
      "unit": "each",
      "qty": 1,
      "vendor": "Online Metals",
      "url": "https://www.onlinemetals.com/buy/0-75-carbon-steel-plate-a36-hot-rolled/pid/9614",
      "verified": "page",
      "role": "primary",
      "notes": "30.6 lb blank, tolerance +/- 0.125 in. Heavy - freight."
    },
    {
      "id": "A6",
      "category": "A. Foundation and mast",
      "item": "Steel angle, 2 x 2 x 1/4 in, A36 hot rolled, 10 ft",
      "used_for": "Four base-plate gussets plus mast-top brackets",
      "part_number": "A12214",
      "price_usd": 64.50,
      "unit": "each",
      "qty": 1,
      "vendor": "Metals Depot",
      "url": "https://www.metalsdepot.com/steel-products/steel-angle",
      "verified": "page",
      "role": "primary",
      "notes": "3.19 lb/ft. Stocked 2/4/6/8/10/20 ft; 10 ft = $64.50, 6 ft = $45.02."
    },
    {
      "id": "A7",
      "category": "A. Foundation and mast",
      "item": "Post-installed concrete screw anchor, 3/4 in x 8-1/2 in (Simpson Strong-Tie Titen HD), box of 5",
      "used_for": "Anchoring the base plate to the cured pier - 4 anchors",
      "part_number": "THD75812H",
      "price_usd": 59.09,
      "unit": "per box of 5",
      "qty": 1,
      "vendor": "Concrete Fasteners",
      "url": "https://www.concretefasteners.com/3-4-x-8-1-2-simpson-strong-tie/",
      "verified": "page",
      "role": "primary",
      "notes": "Zinc plated. Sold only in boxes of 5; need 4, so one box. Alternate: Home Depot 5-pack THD75812H $55.74 (listing), Fasteners Plus $57.99."
    },

    {
      "id": "B1",
      "category": "B. Yaw (weathervane) axis - the main thrust bearing",
      "item": "iglide PRT-01-100-DD slewing ring, fully sealed both faces, aluminium housing, iglide J sliding elements",
      "used_for": "The one large thrust bearing the whole branch turns on",
      "part_number": "PRT-01-100-DD (igus art. PRT-01-100-DD)",
      "price_usd": 398.83,
      "unit": "each",
      "qty": 1,
      "vendor": "igus",
      "url": "https://www.igus.com/product/iglidur_PRT_01_AL_J?artnr=PRT-01-100",
      "verified": "quote",
      "role": "primary",
      "notes": "CHOSEN 2026-11-01 (decision 2): the fully sealed variant - sealing lips on both faces, the version igus describes as built for 'blowing sand... outdoor mounts where both faces see weather'. 185 mm (7.28 in) ring, dry-running sliding elements, NO rolling elements and NO grease. LEAD TIME: 25-30 WORKING DAYS, accepted by Mike and treated as a hard constraint on the build schedule (5-6 calendar weeks; it is the critical-path item). PRICE: igus publishes NO price for the -DD variant - it quotes on request - so THE $398.83 CARRIED HERE IS AN ALLOWANCE, NOT A QUOTATION, and this is the only line in the bill without a real price. The allowance is the published, page-verified price of the same-size standard ring PRT-01-100 (read off the igus product page 2026-11-01), used as the floor: the sealed ring cannot cost less than the ring it is derived from. For scale, in the one size class where igus publishes both variants, 80 mm, the sealed ring is 569.68/216.33 = 2.63x the standard one, which would put a sealed 185 mm ring near $1,050. The concept sheet therefore gives the total both ways. Replace this line with igus' written quotation before ordering anything. See Risk 1."
    },
    {
      "id": "B2",
      "category": "B. Yaw (weathervane) axis - the main thrust bearing",
      "item": "Steel plate, A36, 12 x 12 x 1/2 in, cut to size",
      "used_for": "Fixed adapter plate under the slewing ring and matching rotating plate above it",
      "part_number": "9612",
      "price_usd": 78.55,
      "unit": "each",
      "qty": 1,
      "vendor": "Online Metals",
      "url": "https://www.onlinemetals.com/buy/0-5-carbon-steel-plate-a36-hot-rolled/pid/9612",
      "verified": "page",
      "role": "primary",
      "notes": "One 12 x 12 blank yields both 7 in plates and the drill jig. Bolt pattern is taken from the igus CAD for PRT-01-100 (downloadable from the product page)."
    },
    {
      "id": "B3",
      "category": "B. Yaw (weathervane) axis - the main thrust bearing",
      "item": "Update International 1 qt stainless steel mixing bowl (7.75 in dia x 2.38 in deep)",
      "used_for": "The 'bud' - inverted over the slewing ring as a drip hat that sheds rain and meltwater off the bearing gap",
      "part_number": "Staples Item 453546 / Model 78701",
      "price_usd": 8.99,
      "unit": "each",
      "qty": 1,
      "vendor": "Staples",
      "url": "https://www.staples.com/Update-International-1-qt-Stainless-Steel-Mixing-Bowl/product_453546",
      "verified": "page",
      "role": "primary",
      "notes": "Cheapest and most in-keeping seal in the list - its radius matches the 185 mm ring almost exactly, and it reads as a bud rather than as hardware."
    },

    {
      "id": "C1",
      "category": "C. Nod (lean) axis",
      "item": "UCFL205-16 two-bolt flange bearing unit, 1 in bore, cast iron, self-aligning, rubber seal, grease zerk",
      "used_for": "The two bearings the boom leans on",
      "part_number": "UCFL205-16 (Zoro # G0071471, Tritan)",
      "price_usd": 24.89,
      "unit": "each",
      "qty": 2,
      "vendor": "Zoro",
      "url": "https://www.zoro.com/tritan-2-bolt-flange-bearing-ball-insert-1-bore-ucfl205-16/i/G0071471/",
      "verified": "listing",
      "role": "primary",
      "notes": "Bolted on rather than bored into a fabrication - this is what removes the machine-shop operation from the nod axis. Self-aligning insert forgives weld distortion. Sealed and relubricatable; primary tension-free operation, one grease-gun stroke per year. Price spread across vendors: Surplus Center $12.10, BearingsDirect $18.00, Zoro $24.89, FYH $43.77 - all for the same UCFL205-16."
    },
    {
      "id": "C2",
      "category": "C. Nod (lean) axis",
      "item": "1 in carbon steel round bar, 1018 cold finish, 12 in",
      "used_for": "Nod pivot pin (7 in) and the counterweight stub (5 in)",
      "part_number": "4797",
      "price_usd": 11.62,
      "unit": "each",
      "qty": 2,
      "vendor": "Online Metals",
      "url": "https://www.onlinemetals.com/en/buy/carbon-steel/1-carbon-steel-round-bar-1018-cold-finish/pid/4797",
      "verified": "page",
      "role": "primary",
      "notes": "Length ladder on page: $11.62 up to $84.24. Two pieces cover the pin and the stub; the 1018 turns cleanly to a bearing fit and takes paint."
    },
    {
      "id": "C3",
      "category": "C. Nod (lean) axis",
      "item": "1 x 2 x 1 in rectangle urethane bumper, 80A",
      "used_for": "Four pads that both limit the lean and act as the return spring, so the boom always eases back to the same attitude",
      "part_number": "REC003",
      "price_usd": 7.27,
      "unit": "each",
      "qty": 4,
      "vendor": "Acrotech",
      "url": "https://www.acrotechinc.com/product/1x2x1-rectangle-bumper-rec003/",
      "verified": "page",
      "role": "primary",
      "notes": "Pre-drilled and counterbored for 1/4 in socket head cap screws. This part is the whole answer to 'why is this not a Calder knockoff' - it makes the lean a spring, not a swing. Pick the durometer when ordering (40A softest / 95A hardest); 80A is the starting point."
    },

    {
      "id": "D1",
      "category": "D. Boom, stalks and balance",
      "item": "Steel round tube, 2-1/2 in OD x 0.120 in wall, A513 welded HREW, 20 ft",
      "used_for": "The boom - 12 ft cut from this",
      "part_number": "T2W212120",
      "price_usd": 150.60,
      "unit": "each",
      "qty": 1,
      "vendor": "Metals Depot",
      "url": "https://www.metalsdepot.com/steel-products/steel-round-tube-welded",
      "verified": "page",
      "role": "primary",
      "notes": "3.05 lb/ft, so the 12 ft boom is 37 lb. Stocked only in 4/6/8/10/20 ft - there is NO 12 ft length, so buy the 20 ft piece and keep 8 ft as stock for brackets. 10 ft = $99.10. Freight."
    },
    {
      "id": "D2",
      "category": "D. Boom, stalks and balance",
      "item": "Steel round tube, 1-1/2 in OD x 0.120 in wall, A513, 12 ft",
      "used_for": "The five bloom stalks",
      "part_number": "866TF9 (mfr HTR/1500120-144)",
      "price_usd": 140.00,
      "unit": "each",
      "qty": 1,
      "vendor": "Grainger",
      "url": "https://www.grainger.com/product/Carbon-Steel-Round-Tube-A513-866TF9",
      "verified": "page",
      "role": "primary",
      "notes": "Exactly 12 ft, which is the length the five stalk cuts need (40+34+28+22+16 in = 140 in). Alternate: Metals Depot welded T2W112120 at 10 ft $66.30 or DOM T2112120 at 20 ft $134.40."
    },
    {
      "id": "D3",
      "category": "D. Boom, stalks and balance",
      "item": "Steel round tube, 1-1/4 in OD x 3/16 in wall, A513-T5 DOM, 6 ft (0.874 in / 22.2 mm bore)",
      "used_for": "Five short collars welded where each stalk meets the boom, to spread the load into the boom wall",
      "part_number": "T2114316",
      "price_usd": 72.30,
      "unit": "each",
      "qty": 1,
      "vendor": "Metals Depot",
      "url": "https://www.metalsdepot.com/steel-products/steel-round-tube-dom",
      "verified": "page",
      "role": "primary",
      "notes": "2.14 lb/ft. Stocked 1/2/4/6/8/10/20 ft; 6 ft = $72.30, 1 ft = $14.55. Its 22.2 mm bore is also a spare-fit for the 608 bearings, which is why it is worth having in the shop."
    },
    {
      "id": "D4",
      "category": "D. Boom, stalks and balance",
      "item": "CAP Barbell standard cast iron weight plate, 25 lb, 1 in bore, black",
      "used_for": "Counterweight on the butt of the boom - the piece that makes the boom balance",
      "part_number": "Walmart Business item 20470506 (CAP standard 1 in plate)",
      "price_usd": 34.97,
      "unit": "each",
      "qty": 2,
      "vendor": "Walmart",
      "url": "https://business.walmart.com/ip/CAP-Barbell-Standard-Cast-Iron-Weight-Plate-25-Lbs-Black/20470506",
      "verified": "page",
      "role": "primary",
      "notes": "1 in bore slides straight onto the 1 in 1018 counterweight stub (C2), which is why this is the plate to buy rather than an Olympic plate. Two plates = 50 lb of trim; balance is set by sliding them along the stub and locking with a 1 in shaft collar. If 50 lb is not enough the plate can be had at 50 lb / $68.97."
    },
    {
      "id": "D5",
      "category": "D. Boom, stalks and balance",
      "item": "PATIKIL 2-1/2 in plastic tubing end caps, 12 pcs",
      "used_for": "Closing the open ends of the boom tube so water cannot fill it and split the welds in a freeze",
      "part_number": "Lowes item 8711039 / model S26020200UX1305",
      "price_usd": 11.99,
      "unit": "per 12-pack",
      "qty": 1,
      "vendor": "Lowe's",
      "url": "https://www.lowes.com/pd/PATIKIL-2-1-2inch-Plastic-Tubing-End-Caps-12pcs-Round-Hole-Plug-Insert-for-Round-Iron-Pipe-Chair-Leg-Table-Bookshelves-Patio-Furniture-Black/8711039",
      "verified": "page",
      "role": "primary",
      "notes": "Also drill a 3/16 in weep hole at the lowest point of every closed tube volume - the plug seals the end, the weep hole makes sure nothing can stand inside."
    },
    {
      "id": "D6",
      "category": "D. Boom, stalks and balance",
      "item": "PATIKIL 1-1/4 in plastic tubing end caps, 40 pcs",
      "used_for": "Closing the stalk tube ends and the stub tube",
      "part_number": "Lowes item 8059932",
      "price_usd": 12.99,
      "unit": "per 40-pack",
      "qty": 1,
      "vendor": "Lowe's",
      "url": "https://www.lowes.com/pd/PATIKIL-1-1-4inch-Plastic-Tubing-End-Caps-40pcs-Round-Hole-Plug-Insert-for-Round-Iron-Pipe-Chair-Leg-Table-Bookshelves-Patio-Furniture-Black/8059932",
      "verified": "page",
      "role": "primary",
      "notes": "40 off is far more than the 10 needed - the balance is spares, and they also fit the boom's 1-1/4 in DOM collars."
    },

    {
      "id": "E1",
      "category": "E. Blooms (5 off)",
      "item": "Update International 8 qt stainless steel mixing bowl, 13-1/4 in dia x 4 in deep, 0.4 mm stainless",
      "used_for": "One bowl per bloom - each is cut in half and the two halves are remounted as an offset two-lobe rotor",
      "part_number": "Staples Item 454113 / Model 78705",
      "price_usd": 17.29,
      "unit": "each",
      "qty": 5,
      "vendor": "Staples",
      "url": "https://www.staples.com/update-international-8-qt-stainless-steel-mixing-bowl/product_454113",
      "verified": "page",
      "role": "primary",
      "notes": "CHOSEN 2026-11-01 (decision 4): the THIN 0.4 mm bowl - motion over toughness. Deliberately a shallow bowl - 13-1/4 in across but only 4 in deep, which is what gives the piece the flat, open 'bloom' proportion rather than a hubcap. Thin is a feature here: low inertia, so a light breeze starts the spin. The trade is recorded plainly rather than sold as a virtue: this bowl WILL DENT, and it is bought because $17.29 makes it cheap to replace, not because it is tough. A partial dent in one lobe makes that bloom run out of true before it stops turning - the rotor still turns, it only loses smoothness. Heavier-gauge alternate with a published price, NOT chosen and NOT priced into the total: Choice 8 Qt Heavy Weight stainless mixing bowl, WebstaurantStore item 407MIXHDN08, $9.59 each."
    },
    {
      "id": "E2",
      "category": "E. Blooms (5 off)",
      "item": "Stainless round tube 316 seamless, 1 in OD x 0.065 in wall x 0.87 in ID (22.1 mm bore)",
      "used_for": "Bloom hub - the housing the two 608 bearings press into",
      "part_number": "Online Metals 12960",
      "price_usd": 18.40,
      "unit": "per 12 in",
      "qty": 3,
      "vendor": "Online Metals",
      "url": "https://www.onlinemetals.com/en/buy/stainless-steel/1-od-x-0-065-wall-x-0-87-id-stainless-round-tube-316-seamless/pid/12960",
      "verified": "page",
      "role": "primary",
      "notes": "0.66 lb per 12 in. The 0.87 in ID is 22.1 mm, a light press fit on a 22 mm bearing OD. 316 stainless, so the hub can stand wet and does not need paint inside the bearing bore. Length ladder on page $18.40 up to $267.78; 3 ft covers 5 hubs at 6 in each plus 6 in of spare."
    },
    {
      "id": "E3",
      "category": "E. Blooms (5 off)",
      "item": "8 mm x 100 mm case-hardened chrome-plated linear motion shaft, pack of 5, HRC60, h8 tolerance",
      "used_for": "The five bloom axles - the shafts the blooms spin on",
      "part_number": "VXB 8mm-100mm-hardened-linear-motion-shafts (5-pack)",
      "price_usd": 49.93,
      "unit": "per 5-pack",
      "qty": 1,
      "vendor": "VXB Bearings",
      "url": "https://vxb.com/products/8mm-100mm-hardened-linear-motion-shafts",
      "verified": "page",
      "role": "primary",
      "notes": "Ground to h8, which is the fit a 608 bearing inner ring wants - do not substitute ordinary 8 mm bar stock, it is undersized and the inner ring will creep. Case hardened to HRC60 so the 1 in 1018 nod pin load is nowhere near its limit. Alternate 4-pack at $47.95."
    },
    {
      "id": "E4",
      "category": "E. Blooms (5 off)",
      "item": "608-2RS sealed ball bearing, 8 x 22 x 7 mm (double rubber sealed)",
      "used_for": "Two per bloom - the spin bearings; one part number for every rotating joint at the blooms",
      "part_number": "VXB 10-pack 608-2RS 8x22x7mm sealed",
      "price_usd": 14.99,
      "unit": "per 10-pack",
      "qty": 2,
      "vendor": "VXB Bearings",
      "url": "https://vxb.com/products/10-pack-skateboard-bearing-608-2rs-sealed-8x22x7mm",
      "verified": "page",
      "role": "primary",
      "notes": "10 needed, 20 bought - the extra 10 are the spares kit, because the whole service story for 'a sticky bloom' depends on being able to swap a bearing on the spot. $1.50 a bearing. 2RS = rubber contact seals both sides. Stainless upgrade if wanted: S608-2RS, VXB, $19.99."
    },
    {
      "id": "E5",
      "category": "E. Blooms (5 off)",
      "item": "Steel plate, A36, 1/4 in x 12 x 12 in, cut to size",
      "used_for": "Hub caps (top and bottom plates of each bloom hub, 10 discs) and the two nod-yoke cheeks - all cut from this plate, no separate purchase",
      "part_number": "9610",
      "price_usd": 27.55,
      "unit": "each",
      "qty": 2,
      "vendor": "Online Metals",
      "url": "https://www.onlinemetals.com/buy/0-25-carbon-steel-plate-a36-hot-rolled/pid/9610",
      "verified": "page",
      "role": "primary",
      "notes": "A 12 x 12 blank yields fourteen 3-1/4 in discs, so one plate covers all ten hub caps; the second plate covers the yoke cheeks and brackets. 10.2 lb each. These discs are a cutting operation on stock already in the list, not a part to source."
    },
    {
      "id": "E6",
      "category": "E. Blooms (5 off)",
      "item": "Stainless round tube 316 seamless, 3/4 in OD x 0.049 in wall x 0.652 in ID, 3 ft",
      "used_for": "Axle sleeves, pipe spacers and the tube the bloom stalks are sleeved with at the tips",
      "part_number": "Online Metals 12952",
      "price_usd": 39.44,
      "unit": "per 3 ft",
      "qty": 1,
      "vendor": "Online Metals",
      "url": "https://www.onlinemetals.com/en/buy/stainless-steel/0-75-od-x-0-049-wall-x-0-652-id-stainless-round-tube-316-seamless/pid/12952",
      "verified": "page",
      "role": "primary",
      "notes": "Length ladder: 1 ft $14.86 / 2 ft $28.92 / 3 ft $39.44 / 6 ft $53.86."
    },
    {
      "id": "E7",
      "category": "E. Blooms (5 off)",
      "item": "Steel flat bar, 1/4 x 2 in, A36 hot rolled, 6 ft",
      "used_for": "Bowl-to-hub clamps, the counterweight stub collar blank and small tabs",
      "part_number": "F2142",
      "price_usd": 26.18,
      "unit": "each",
      "qty": 1,
      "vendor": "Metals Depot",
      "url": "https://www.metalsdepot.com/steel-products/steel-flat-bar",
      "verified": "page",
      "role": "primary",
      "notes": "1.70 lb/ft. Stocked 2/4/6/8/10/20 ft; 6 ft = $26.18."
    },

    {
      "id": "F3",
      "category": "F. Finish, fasteners and service",
      "item": "Single-can direct-to-metal protective enamel, 1 gallon (flat black)",
      "used_for": "THE finish - one coat straight onto prepared steel, no separate primer",
      "part_number": "Rust-Oleum Professional 7776402",
      "price_usd": 53.98,
      "unit": "per gallon",
      "qty": 1,
      "vendor": "The Home Depot",
      "url": "https://www.homedepot.com/p/Rust-Oleum-Professional-1-gal-High-Performance-Protective-Enamel-Flat-Black-Oil-Based-Interior-Exterior-Paint-7776402/202097793",
      "verified": "listing",
      "role": "primary",
      "notes": "CHOSEN 2026-11-01 (decision 3) and PROMOTED FROM ALTERNATE TO PRIMARY: lines F1 (two-part epoxy primer) and F2 (two-part marine LPU) were removed from this bill on the same date, dropping $489.98. Consequences stated, not glossed: this is a SINGLE-COMPONENT oil-based enamel with a SHORTER SERVICE LIFE than the two-part boat system it replaces - expect to recoat, and expect a garden piece rather than a dock piece. That is the trade Mike accepted, and this sheet does not re-argue it. Being direct-to-metal, there is no primer line and none is needed. Coverage 400 sq ft/gal covers the whole armature many times over; one gallon is the price basis for the decision. Page-verified alternate stockist: Runnings at $59.99 (https://www.runnings.com/rust-oleumr-professional-high-performance-protective-enamel-paint-flat-black-gallon-7220692.html). OPEN ITEM, not a BOM quantity: this product line is a FIXED PALETTE that cannot be tinted - Rust-Oleum's own listing says 'cannot be tinted... it's ok to mix paint colors together to get custom colors if they are in the same product line and have the same sheen' - and in this line flat sheen is stocked only in black and white, with the other colours in gloss. Decision 1's charcoal-green / marigold / clay-red are therefore NOT three cans off the shelf. See 'Coating colour' in the concept sheet: mix from stock gallons, accept the nearest stock colour, or move the colour coats to a tintable single-component DTM enamel at similar cost. The BOM carries the flat-black gallon as the decided price basis; the colour coats are priced once that is settled."
    },
    {
      "id": "F4",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 316 socket head cap screws, 1/4 in-20 x 1 in",
      "used_for": "Armature assembly, bracket joints, bumper fixing",
      "part_number": "Bolt Depot product 16540",
      "price_usd": 0.59,
      "unit": "each",
      "qty": 48,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=16540",
      "verified": "page",
      "role": "primary",
      "notes": "Also $43.75 / 100. Quantity is set by the cut list, not a placeholder."
    },
    {
      "id": "F5",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 316 socket head cap screws, 5/16 in-18 x 1-1/4 in",
      "used_for": "Heavier joints and the flange bearing units",
      "part_number": "Bolt Depot product 16550",
      "price_usd": 1.04,
      "unit": "each",
      "qty": 24,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=16550",
      "verified": "page",
      "role": "primary",
      "notes": "$77.35 / 100."
    },
    {
      "id": "F6",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 316 hex nuts, 1/4 in-20",
      "used_for": "Matching nuts for F4",
      "part_number": "Bolt Depot product 15983",
      "price_usd": 0.12,
      "unit": "each",
      "qty": 48,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=15983",
      "verified": "page",
      "role": "primary",
      "notes": "$7.25 / 100. Nylon-insert lock nuts (product 16008, $0.26 each) are the better choice on the bumper and bearing bolts where vibration is possible."
    },
    {
      "id": "F7",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 316 hex nuts, 5/16 in-18",
      "used_for": "Matching nuts for F5",
      "part_number": "Bolt Depot product 15984",
      "price_usd": 0.16,
      "unit": "each",
      "qty": 24,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=15984",
      "verified": "page",
      "role": "primary",
      "notes": "$10.70 / 100."
    },
    {
      "id": "F8",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 316 flat washers, 1/4 in",
      "used_for": "Under 1/4 in heads and nuts",
      "part_number": "Bolt Depot product 16019",
      "price_usd": 0.14,
      "unit": "each",
      "qty": 96,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=16019",
      "verified": "page",
      "role": "primary",
      "notes": "Two per bolt assumed. $9.19 / 100."
    },
    {
      "id": "F9",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 316 flat washers, 5/16 in",
      "used_for": "Under 5/16 in heads and nuts",
      "part_number": "Bolt Depot product 16020",
      "price_usd": 0.16,
      "unit": "each",
      "qty": 48,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=16020",
      "verified": "page",
      "role": "primary",
      "notes": "$9.95 / 100."
    },
    {
      "id": "F10",
      "category": "F. Finish, fasteners and service",
      "item": "Stainless steel 18-8 metric socket head cap screws, M4 x 20 mm",
      "used_for": "Bowl-to-hub-cap fixings (3 per bloom, 5 blooms) and the bearing hat bracket",
      "part_number": "Bolt Depot product 6398",
      "price_usd": 0.11,
      "unit": "each",
      "qty": 60,
      "vendor": "Bolt Depot",
      "url": "https://boltdepot.com/Product-Details?product=6398",
      "verified": "page",
      "role": "primary",
      "notes": "$8.16 / 100. These are the two screws per bloom that come out to lift the rotor off its axle - the service access."
    },
    {
      "id": "F11",
      "category": "F. Finish, fasteners and service",
      "item": "3M 5200 marine adhesive sealant, 10 oz",
      "used_for": "Bedding bolted joints and bearing contact faces, capping tube ends, isolating stainless from aluminium",
      "part_number": "PN06500HC (HD Internet # 202258948)",
      "price_usd": 22.48,
      "unit": "per 10 oz tube",
      "qty": 1,
      "vendor": "The Home Depot",
      "url": "https://www.homedepot.com/p/3M-10-oz-White-5200-Marine-Adhesive-Polyurethane-Sealant-PN06500HC/202258948",
      "verified": "listing",
      "role": "primary",
      "notes": "Permanent, flexible, waterproof. Dissimilar-metal contact (stainless bolts into an aluminium ring housing) is bedded in this to stop galvanic corrosion, which matters more outdoors than the bolted strength does."
    },
    {
      "id": "F12",
      "category": "F. Finish, fasteners and service",
      "item": "Boeshield T-9 water-displacing corrosion protectant, 12 oz aerosol",
      "used_for": "The bare faces and threads that stay assembled and unpainted - the nod pin, the bearing bores, the 608 axles",
      "part_number": "ASIN B0HNT7FM27",
      "price_usd": 21.56,
      "unit": "per can",
      "qty": 2,
      "vendor": "Amazon",
      "url": "https://www.amazon.com/dp/B0HNT7FM27",
      "verified": "page",
      "role": "primary",
      "notes": "Wax-based, dries to a non-greasy film, so it does not hold grit the way oil does. Reapply annually - it is the annual service job on the nod pin. Alternate: ACF-50 13 oz (Amazon B016OMGR0E, about $19-24)."
    }
  ]
}
