# Base Survey — the Permobil chassis

Fill this in **before** any controller is priced or bought. Everything downstream depends on §2.
Have the chair in the shop, wheels off the ground, batteries disconnected, free-wheel levers checked.

Date surveyed: __________  Surveyed by: __________

---

## 1. The machine

| Item | Answer |
|---|---|
| Model on the frame sticker | |
| Serial number | |
| Drive layout | mid-wheel drive? (drive wheels in the middle, casters front and rear) |
| Wheel diameter and type | (pneumatic?) |
| Drive wheel count | 2 |
| Approx. chassis weight | |

## 2. THE MOTORS — the one that decides everything

For **each** motor, look at the cable coming out and count the heavy conductors:

| | Left motor | Right motor |
|---|---|---|
| **Heavy wires** (thick conductors) | | |
| **Thin sensor wires** (a bundle of ~5) | | |
| Part number / label on the motor | | |
| Gearbox part number | | |
| Free-wheel lever present? | | |

**How to read it:**

- **2 heavy wires, no sensor bundle → brushed DC.** The Sabertooth 2x32 route applies.
- **3 heavy wires + a bundle of ~5 thin wires → brushless.** Different controllers, different plan.

> Motor type conclusion: **__________________**
> (circle one) **BRUSHED** / **BRUSHLESS** / **still unknown**

## 3. The brakes

The brakes are separate from the motor conductors. Find those wires.

| Item | Answer |
|---|---|
| Brake wires present on each motor? | |
| Number of brake wires per motor | 2 expected |
| Rated voltage printed on the brake | (24 V expected) |
| Rated current / watts printed on the brake | |
| Brake connector type, if any | (or bare wires?) |
| Manual free-wheel lever works? | (test by hand, power off) |

**Confirm the fail-safe behaviour:** with the batteries disconnected and the levers in *drive*, the
wheels should be **locked**. If they spin freely, the levers are released — fix that before anything
else. *A chair in free-wheel has no brakes at all.*

## 4. What survived on the chassis

| Part | Present? | Notes |
|---|---|---|
| Batteries | yes (Mike) | voltage, Ah rating, and date on them |
| Charger | yes (Mike) | connector type, output voltage |
| Main fuse / breaker / battery harness | | |
| Power module (black controller box) | **NO — gone (rev 4)** | Mike no longer has it. Path A is off: there is nothing left to bench-test |
| Joystick / control panel | **NO — gone (rev 4)** | |
| R-net cables (4-pin, module to module) | **NO — gone (rev 4)** | the whole R-net bus is gone, so the factory-electronics route no longer exists |
| CAN transceiver + ESP32 | ESP32s owned | only needed if we choose CAN-based controllers — not required by default |
| Seat and actuators | | (going or staying?) |
| Lights / wiring loom | | (any of it reusable?) |
| Motor cable stubs — cut or intact connectors? | | **important: cut wires mean re-terminating** |

## 5. Measured facts (multimeter, batteries disconnected)

| Measurement | Reading |
|---|---|
| Battery pack voltage (charged, open circuit) | |
| Battery pack voltage under a load | |
| Continuity between the two brake wires | |
| Resistance across the motor terminals | |
| Any voltage marking on the motor or brake | |

## 6. Evidence — text is enough, photos are optional

**Photographs are NOT required.** Mike cannot take pictures, so do not block on them, and do not
ask for them again. Everything needed can be written down or spoken:

- **The wire count at each motor** (§2) is a number — it is the single fact that decides the
  electronics, and it survives being described rather than photographed.
- **Part numbers and labels** can be typed or dictated.
- Where a photo would have helped, **write what you see in words instead** — shape, colour, how
  many wires, where the connector sits, whether anything is cut.

If photos ever do arrive, save them under `output/base-survey/`. Their absence is expected, not a
gap in the survey: **a completed §2 with a stated wire count is a finished survey.**

### Photos received 2026-11-10

Nine photographs of the base, **taken 26–27 Oct 2018**, supplied by Mike from his OneDrive folder on
the datapool and saved under `output/base-survey/`. They show the chair **already stripped** — base
resting on a crate, battery box out on the floor, no seat or joystick.

**They do NOT settle §2, and cannot.** The motor conductors sit inside the cable sheath; the individual
copper is not visible in any of the nine, so no conductor count can be read from them. One automated
reading volunteered "typically two heavy conductors" for this class of chair — that is an inference
from the chair *type*, **not an observation**, and must never be recorded as the answer. §2 stays open
until someone counts at a bare end or a free connector.

What the photos do establish, and which is worth having:

- **Drive tyres: KENDA**, knobby off-road tread, apparently pneumatic or semi-pneumatic.
- **Suspension:** coil-over shock absorbers on the caster arms — the base is sprung, not rigid.
- **Free-wheel release:** a black plastic lever marked **PUSH / PULL** — this is the lever §3 asks about.
- **Battery box is out of the chair**, on the floor, with a "RECYCLE ME" sticker.
- **Cable marking seen:** "CE-300 CHANGBAO PVC 105C VW-1" — a cable spec, not a motor part number.
- Bare aluminium frame with warning stickers; an "11 LBS" label on one suspension arm.
- No motor, gearbox or frame serial number is legible in any shot.

One automated reading guessed the model was an F-series (F3/F5) from the silhouette. That contradicts
the M300/M3/M1 already recorded, and **must not be used to change the model.** The frame sticker
settles it.

### The spoken numbers that matter most

1. Heavy conductors at each motor: **2** (brushed) or **3 + a ~5-wire bundle** (brushless).
2. Brake wires per motor: expected **2**, and any voltage printed — **24 V** expected.
3. Any part number on a motor, gearbox, or the frame sticker.
4. Whether any of the chair's own electronics survived anywhere — if a box of R-net parts turns up,
   say so before we buy controllers.


## 7. Conclusion

- Motor type: **______________________**
- Controller path chosen: **______________________**
- Anything that contradicts `docs/constraints.md`: **______________________**
- Open questions for Mike: **______________________**
